[UPDATED 2026] Getting NSE7_SDW-7.2 Certification Made Easy!
NSE7_SDW-7.2 Exam Crack Test Engine Dumps Training With 101 Questions
NEW QUESTION # 41
Refer to the exhibits.
An administrator is testing application steering in SD-WAN. Before generating test traffic, the administrator collected the information shown in exhibit A.
After generating GoToMeeting test traffic, the administrator examined the respective traffic log on FortiAnalyzer, which is shown in exhibit B. The administrator noticed that the traffic matched the implicit SD-WAN rule, but they expected the traffic to match rule ID 1.
Which two reasons explain why the traffic matched the implicit SD-WAN rule? (Choose two.)
- A. Port1 and port2 do not have a valid route to the destination.
- B. FortiGate did not refresh the routing information on the session after the application was detected.
- C. The session 3-tuple did not match any of the existing entries in the ISDB application cache.
- D. Full SSL inspection is not enabled on the matching firewall policy.
Answer: B,C
Explanation:
Study guide 7.2 Page 191
NEW QUESTION # 42
Refer to the exhibit.
The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured latency will make T_MPLS_0 the new preferred member?
- A. When T_MPLS_0 has a latency of 100 ms.
- B. When T_N1PLS_0 has a latency of 80 ms.
- C. When T_INET_0_0 and T_MPLS_0 have the same latency.
- D. When T_INET_0_0 has a latency of 250 ms.
Answer: B
NEW QUESTION # 43 
Two hub-and-spoke groups are connected through a site-to-site IPsec VPN between Hub 1 and Hub 2. The administrator configured ADVPN on both hub-and-spoke groups.
Which two outcomes are expected if a user in Toronto sends traffic to London? (Choose two.)
- A. Traffic from Toronto to London triggers the dynamic negotiation of a direct site-to-site VPN.
- B. The first packets from Toronto to London are routed through Hub 1 then to Hub 2.
- C. Toronto needs to establish a site-to-site tunnel with Hub 2 to bypass Hub 1.
- D. London generates an IKE information message that contains the Toronto public IP address.
Answer: A,B
NEW QUESTION # 44
Refer to the exhibit.
Based on the exhibit, which two actions does FortiGate perform on traffic passing through port2? (Choose two.)
- A. FortiGate does not change the routing information on existing sessions that use a valid gateway, after a route change.
- B. FortiGate always blocks all traffic, after a route change.
- C. FortiGate performs routing lookups for new sessions only, after a route change.
- D. FortiGate flushes all routing information from the session table, after a route change.
Answer: A,C
NEW QUESTION # 45
Which CLI command do you use to perform real-time troubleshooting for ADVPN negotiation?
- A. get router info routing-table all
- B. diagnose debug application ike
- C. diagnose vpn tunnel list
- D. get ipsec tunnel list
Answer: B
Explanation:
IKE real-time debug - useful when debugging ADVPN shortcut messages and spoke-to-spoke negotiations.
* diagnose debug console timestamp enable
* diagnose vpn ike log filter clear
* diagnose vpn ike log filter mdst-addr4 <ip.of.hub> <ip.of.spoke>
* diagnose debug application ike -1
* diagnose debug enable
NEW QUESTION # 46
Exhibit.
The exhibit shows VPN event logs on FortiGate. In the output shown in the exhibit, which statement is true?
- A. There is one shortcut tunnel built from master tunnel T_MPLS_0.
- B. The VPN tunnel T_MPLS_0 is a shortcut tunnel.
- C. The master tunnel T_INET_0 cannot accept the ADVPN shortcut.
- D. There are no IPsec tunnel statistics log messages for ADVPN cuts.
Answer: B
NEW QUESTION # 47
Refer to the exhibit.
Based on the output, which two conclusions are true? (Choose two.)
- A. The all_rules rule represents the implicit SD-WAN rule.
- B. The SD-WAN rules take precedence over regular policy routes.
- C. There is more than one SD-WAN rule configured.
- D. Entry 1(id=1) is a regular policy route.
Answer: C,D
NEW QUESTION # 48
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit A shows the SD-WAN performance SLA configuration, the SD-WAN rule configuration, and the application IDs of Facebook and YouTube. Exhibit B shows the firewall policy configuration and the underlay zone status.
Based on the exhibits, which two statements are correct about the health and performance of port1 and port2?
(Choose two.)
- A. Non-TCP Facebook and YouTube traffic are not used for performance measurement.
- B. FortiGate is unable to measure jitter and packet loss on Facebook and YouTube traffic.
- C. FortiGate identifies the member as dead when there is no Facebook and YouTube traffic passing through the member.
- D. The performance is an average of the metrics measured for Facebook and YouTube traffic passing through the member.
Answer: A,D
Explanation:
Study Guide 7.2, pages 103 - 104. Another comment said "because without using application Control on the firewall policy, SDWAN can't work" but there is a app control "default" defined on config.
NEW QUESTION # 49
Exhibit.
The exhibit shows the output of the command diagnose sys sdwan health-check status collected on a FortiGate device. Which two statements are correct about the health check status on this FortiGate device?
(Choose two.)
- A. The interface T_INET_1 missed one SLA target.
- B. There is no SLA criteria configured for the health-check Level3_DNS.
- C. The interface T_INET_0 missed three SLA targets.
- D. The health-check VPN_PING orders the members according to the lowest jitter.
Answer: B,D
Explanation:
According to the FortiGate / FortiOS 6.4.2 Administration Guide, the health check status command displays the status of the health check probes for each SD-WAN member interface. The output includes the following information:
* state: the current state of the interface, either alive or dead
* packet-loss: the percentage of packets lost during the health check
* latency: the average round-trip time in milliseconds
* jitter: the variation in latency
* mos: the mean opinion score, a measure of voice quality
* bandwidth: the available bandwidth in kilobits per second for each direction (up, down, bi)
* sla map: a bitmap that indicates which SLA criteria are met or failed Based on the exhibit, the following statements are correct:
* The health-check VPN_PING orders the members according to the lowest jitter. This means that the interface with the lowest jitter value is listed first, followed by the next lowest, and so on1. In the exhibit, the order is T_MPLS, T_INET_1, and T_INET_0.
* There is no SLA criteria configured for the health-check Level3_DNS. This means that the health check does not use any SLA parameters to determine the state of the interface2. In the exhibit, the sla map value is 0x0 for both port1 and port2, indicating that no SLA criteria are applied.
NEW QUESTION # 50
Refer to the exhibit.
The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured latency will make T_MPLS_0 the new preferred member?
- A. When T_MPLS_0 has a latency of 100 ms.
- B. When T_N1PLS_0 has a latency of 80 ms.
- C. When T_INET_0_0 and T_MPLS_0 have the same latency.
- D. When T_INET_0_0 has a latency of 250 ms.
Answer: B
NEW QUESTION # 51
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit A shows the source NAT (SNAT) global setting and exhibit B shows the routing table on FortiGate.
Based on the exhibits, which two actions does FortiGate perform on existing sessions established over port2, if the administrator increases the static route priority on port2 to 20? (Choose two.)
- A. FortiGate continues routing the sessions with no SNAT, over port2.
- B. FortiGate flags the sessions as dirty.
- C. FortiGate updates the gateway information of the sessions with SNAT so that they use port1 instead of port2.
- D. FortiGate performs a route lookup for the original traffic only.
Answer: A,C
NEW QUESTION # 52
Refer to the exhibit.
FortiGate has multiple dial-up VPN interfaces incoming on port1 that match only FIRST_VPN.
Which two configuration changes must be made to both IPsec VPN interfaces to allow incoming connections
to match all possible IPsec dial-up interfaces? (Choose two.)
- A. Use different proposals are used between the interfaces.
- B. Specify a unique peer ID for each dial-up VPN interface.
- C. Use unique Diffie Hellman groups on each VPN interface.
- D. Configure the IKE mode to be aggressive mode.
Answer: B,D
NEW QUESTION # 53
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit A shows the SD-WAN performance SLA configuration, the SD-WAN rule configuration, and the application IDs of Facebook and YouTube. Exhibit B shows the firewall policy configuration and the underlay zone status.
Based on the exhibits, which two statements are correct about the health and performance of port1 and port2? (Choose two.)
- A. Non-TCP Facebook and YouTube traffic are not used for performance measurement.
- B. FortiGate is unable to measure jitter and packet loss on Facebook and YouTube traffic.
- C. FortiGate identifies the member as dead when there is no Facebook and YouTube traffic passing through the member.
- D. The performance is an average of the metrics measured for Facebook and YouTube traffic passing through the member.
Answer: A,D
Explanation:
Study Guide 7.2, pages 103 - 104. Another comment said "because without using application Control on the firewall policy, SDWAN can't work" but there is a app control "default" defined on config.
NEW QUESTION # 54
Refer to the exhibits.
Exhibit A shows the SD-WAN rule status and the learned BGP routes with community 65000:10.
Exhibit B shows the SD-WAN rule configuration, the BGP neighbor configuration, and the route map
configuration.
The administrator wants to steer corporate traffic using routes tags in the SD-WAN rule ID 1.
However, the administrator observes that the corporate traffic does not match the SD-WAN rule ID 1.
Based on the exhibits, which configuration change is required to fix issue?
- A. In the BGP neighbor configuration, apply the route map dcl-lab-rm in the outbound direction.
- B. In SD-WAN rule ID 1, change the destination to use ISDB entries.
- C. In the dcl-lab-rm route map configuration, unset match-community.
- D. In the dcl-lab-rm route map configuration, set set-route-tag to 10.
Answer: A
NEW QUESTION # 55
Refer to the exhibits.
Exhibit A -
Exhibit B -
Exhibit A shows the SD-WAN performance SLA and exhibit B shows the SD-WAN member status, the routing table, and the performance SLA status.
If port2 is detected dead by FortiGate, what is the expected behavior?
- A. The administrator manually restores the static routes for port2, if port2 becomes alive.
- B. Port2 becomes alive after three successful probes are detected.
- C. FortiGate removes all static routes for port2.
- D. Host 8.8.8.8 is reachable through port1 and port2.
Answer: C
Explanation:
This is due to Update static route is enable which removes the static route entry referencing the interface if the interface is dead
NEW QUESTION # 56
What are two benefits of using forward error correction (FEC) in IPsec VPNs? (Choose two.)
- A. FEC transmits parity packets that can be used to reconstruct packet loss.
- B. FEC improves reliability of noisy links.
- C. FEC can leverage multiple IPsec tunnels for parity packets transmission.
- D. FEC supports hardware offloading.
Answer: A,B
NEW QUESTION # 57 
Which two conclusions for traffic that matches the traffic shaper are true? (Choose two.)
- A. The traffic shaper drops packets if the bandwidth is less than 2500 KBps.
- B. The measured bandwidth is less than 100 KBps.
- C. The traffic shaper drops packets if the bandwidth exceeds 6250 KBps.
- D. The traffic shaper limits the bandwidth of each source IP to a maximum of 6250 KBps.
Answer: B,C
NEW QUESTION # 58
Refer to the exhibit, which shows the IPsec phase 1 configuration of a spoke.
What must you configure on the IPsec phase 1 configuration for ADVPN to work with SD-WAN?
- A. You must set ike-version to 1.
- B. You must enable net-device.
- C. You must enable auto-discovery-sender.
- D. You must disable idle-timeout.
Answer: B
NEW QUESTION # 59
Refer to the exhibit.
Based on the exhibit, which statement about FortiGate re-evaluating traffic is true?
- A. The type of traffic defined and allowed on firewall policy ID 1 is UDP.
- B. Changes have been made on firewall policy ID 1 on FortiGate.
- C. Firewall policy ID 1 has source NAT disabled.
- D. FortiGate has terminated the session after a change on policy ID 1.
Answer: B
NEW QUESTION # 60
Which two tasks are part of using central VPN management? (Choose two.)
- A. You must enable VPN zones for SD-WAN deployments.
- B. You configure VPN communities to define common IPsec settings shared by all VPN gateways.
- C. You can configure full mesh, star, and dial-up VPN topologies.
- D. FortiManager installs VPN settings on both managed and external gateways.
Answer: B,C
NEW QUESTION # 61
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit A shows the SD-WAN performance SLA configuration, the SD-WAN rule configuration, and the application IDs of Facebook and YouTube. Exhibit B shows the firewall policy configuration and the underlay zone status.
Based on the exhibits, which two statements are correct about the health and performance of port1 and port2?
(Choose two.)
- A. Non-TCP Facebook and YouTube traffic are not used for performance measurement.
- B. FortiGate is unable to measure jitter and packet loss on Facebook and YouTube traffic.
- C. FortiGate identifies the member as dead when there is no Facebook and YouTube traffic passing through the member.
- D. The performance is an average of the metrics measured for Facebook and YouTube traffic passing through the member.
Answer: A,D
Explanation:
Study Guide 7.2, pages 103 - 104. Another comment said "because without using application Control on the firewall policy, SDWAN can't work" but there is a app control "default" defined on config.
NEW QUESTION # 62
Refer to the exhibit.
The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured latency will make T_MPLS_0 the new preferred member?
- A. When T_MPLS_0 has a latency of 100 ms.
- B. When T_N1PLS_0 has a latency of 80 ms.
- C. When T_INET_0_0 and T_MPLS_0 have the same latency.
- D. When T_INET_0_0 has a latency of 250 ms.
Answer: B
NEW QUESTION # 63
......
Fortinet NSE7_SDW-7.2 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
NSE7_SDW-7.2 Exam Dumps Contains FREE Real Quesions from the Actual Exam: https://www.newpassleader.com/Fortinet/NSE7_SDW-7.2-exam-preparation-materials.html
Obtain the NSE7_SDW-7.2 PDF Dumps Get 100% Outcomes Exam Questions For You To Pass: https://drive.google.com/open?id=1LGmTOXxd-LnUJ5izE5oY1zu0YYhxxvND