Pass NACE-CIP2-001 Exam in First Attempt Guaranteed 2024 Dumps!
NACE-CIP2-001 Dumps Full Questions - Exam Study Guide
NEW QUESTION # 20
Individuals conducting Coating Surveys should:
- A. Always be experienced Specification Writers
- B. Always be NACE Level 3 Certified Inspectors
- C. Always be NACE or SSPC Protective coating Specialists
- D. Always be trained and experienced Coating Industry
Answer: D
NEW QUESTION # 21
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Midstream
- B. Distribution
- C. Gathering
- D. Transmission
Answer: B
NEW QUESTION # 22
Surface preparation of concrete is performed using:
- A. Methods that are the same as wood
- B. Methods that are completely different to steel
- C. Methods that are exactly the same as steel
- D. Methods that have been modified for concrete
Answer: D
NEW QUESTION # 23
Antifouling coatings are regulated by international treaties.
- A. False
- B. True
Answer: B
NEW QUESTION # 24
NACE No.13/ SSPC 6 identifies the use of:
- A. Various methods of cleaning
- B. Watterjetting only
- C. Steam cleaning only
- D. Abrasive blasting only
Answer: A
NEW QUESTION # 25
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings are more durable than coatings.
- B. coatings are expected to degrade over time.
- C. linings protect the contents and the container.
- D. coatings are more durable than linings.
Answer: C
NEW QUESTION # 26
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by acid etching
- B. SP 1 followed by SP 2
- C. SP 1 followed by SP 3
- D. SP 1 followed by caustic etching
Answer: B
NEW QUESTION # 27
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Concrete
- B. Heat-shrink sleeves
- C. Coal Tar Enamel
- D. Liquid epoxies
Answer: D
NEW QUESTION # 28
Inspector reports should always be copied to:
- A. Whomever the Owner identifies
- B. The Contractor and Owner
- C. The Owner only
- D. All parties involved in the project
Answer: A
NEW QUESTION # 29
Examples of non-ferrous metals include
Select All that Apply:
- A. mild steel.
- B. copper
- C. aluminum
- D. iron
Answer: B,C
NEW QUESTION # 30
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method B - X cut
- B. Method A - X Cut
- C. Method A - Cross Hatch
- D. Method B - Cross Hatch
Answer: B
NEW QUESTION # 31
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Document the readings at the end of the shift
- B. Call your supervisor
- C. Advise the coating applicator supervisor of your readings
- D. Check to See if the dehumidification equipment is operating correctly
Answer: C
NEW QUESTION # 32
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Ignore the additional requirement
- B. Request clarification from the specifier
- C. Call your supervisor
- D. Enforce the additional requirement
Answer: D
NEW QUESTION # 33
When observing fabrication defects the NACE Inspector should:
- A. Stop the job immediately
- B. Consult the specification to determine how they should be treated
- C. Require they be corrected prior to coating
- D. Write an NCR and call the fabricator
Answer: B
NEW QUESTION # 34
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. True
- B. False
Answer: B
NEW QUESTION # 35
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Review the specification with the other inspector to see what method was specified
- B. Advise your QC Manager to change the ITP to the use of the salt smart meter
- C. Advise the other inspector he is using an incorrect method
- D. Redo the pre-cleaning based on the other inspectors results
Answer: A
NEW QUESTION # 36
NACE Standards include:
- A. Material Requirements
- B. a) only
- C. Standard Practices
- D. a) & b)
Answer: D
NEW QUESTION # 37
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Challenge the supervisor's authority
- B. Express a willingness to work with the site team and follow the specification
- C. Suggest to the Owner that the supervisor should be removed from site
- D. Defend the previous inspector
Answer: B
NEW QUESTION # 38
It is always possible to see moisture on a steel substrate:
- A. True
- B. False
Answer: B
NEW QUESTION # 39
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A hardness tester
- B. A destructive paint inspection Tooke gauge
- C. A mechanical adhesion tester
- D. A set of 14 pencils of varying hardness
Answer: B
NEW QUESTION # 40
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Stop the job
- B. Advise the Owner and write a Non-Conformance report
- C. Ignore the situation
- D. Require the Applicator to remove the coating
Answer: D
NEW QUESTION # 41
......
CIP Level 2 Free Certification Exam Material from NewPassLeader with 100 Questions: https://www.newpassleader.com/NACE/NACE-CIP2-001-exam-preparation-materials.html
Use Real NACE-CIP2-001 - 100% Cover Real Exam Questions: https://drive.google.com/open?id=1OA5ghJciWJm4AVC05bFiG9lAM_5f1mKV